Configure Enterprise Extender
- 1 Background
- 2 Configuring the different aspects
- 3 Making changes to Network attributes
- 4 Creating the controller description
- 5 Creating the devices descriptions
- 6 Changes to system values
- 7 Changes to Configuration lists
- 8 Opening of firewall ports
- 9 Troubleshooting
Enterprise Extender is used to encapsulate SNA traffic over an IP link. This negates the use of special SNA routers and controllers. It is only available from V5R4 on the iSeries.
Configuring the different aspects
The following changes need to be implemented on the iSeries system, in order to communicate with another system running EE:
- Network attributes
- Create the APPC Controller description
- Create the two APPC devices
- Change system values
- Change configuration lists
- Change ports on the firewalls
Making changes to Network attributes
The following items need to be set in the network attributes, using the CHGNETA command:
APPN node type . . . . . . . . . . . . . . . . . . . . . : *NETNODE Allow APPN virtual support . . . . . . . . . . . . . . . : *NO Allow HPR transport tower support . . . . . . . . . . . : *YES
NB: Changing the node type will require you to vary off ALL APPC controllers and devices before changes are made.
Creating the controller description
Use the CRTCTLAPPC command. Press F4, and define the following parameters:
Controller Description: Name of the controller Link type: *HPRIP APPN-Capable: *YES Remote internet address: The IP address of the remote system Local internet address: The IP address your (local) system Remote network identifier: The SNA network name of the remote system Remote control point: The system name of the remote system APPN CP Session Support: *YES APPN transmission group number: Specify the TGN Number. Must the same on both systems.
Create Ctl Desc (APPC) (CRTCTLAPPC) Type choices, press Enter. Controller description . . . . . SNAHOST Name Link type . . . . . . . . . . . > *HPRIP *ANYNW, *FAX, *FR, *HPRIP... APPN-capable . . . . . . . . . . > *YES *YES, *NO Remote internet address . . . . > ‘18.104.22.168’ Local internet address . . . . . > ‘22.214.171.124’ Remote network identifier . . . > APPN Remote control point . . . . . . > MAINFRAME Name, *ANY APPN CP session support . . . . *YES *YES, *NO APPN transmission group number 1 1-20, *SAME, *CALC
Creating the devices descriptions
You have to use the CRTDEVAPPC command twice, first to setup the name of the device to connect to on the remote system, and secondly a device with the same name as the remote system. Press F4 and define the following parameters:
Device description: Name of the device / remote system name Remote location: Name of the device as defined on the other system / remote system name Local location: Name of local device / local system name. This device does not need to exist locally, but it must look exactly as it is defined on the remote system pointing to you. Remote network identifier: The SNA network name of the remote system Attached controller: Name of the controller under which this device will be located Mode: Using *NETATR should be sufficient, otherwise define the mode you wish to use. APPN-Capable: *YES
Example – Remote device name
Create Device Desc (APPC) (CRTDEVAPPC) Type choices, press Enter. Device description . . . . . . . SNADEVRMT Name Remote location . . . . . . . . > SNADEVRMT Name Online at IPL . . . . . . . . . > *YES *YES, *NO Local location . . . . . . . . . > SNADEVLCL Name, *NETATR Remote network identifier . . . > APPN Name, *NETATR, *NONE Attached controller . . . . . . > SNAHOST Name Mode . . . . . . . . . . . . . . > *NETATR Name, *NETATR APPN-capable . . . . . . . . . . > *YES *YES, *NO
Example – Remote system name
Create Device Desc (APPC) (CRTDEVAPPC) Type choices, press Enter. Device description . . . . . . . MAINFRAME Name Remote location . . . . . . . . > MAINFRAME Name Online at IPL . . . . . . . . . > *YES *YES, *NO Local location . . . . . . . . . > AS400NAME Name, *NETATR Remote network identifier . . . > APPN Name, *NETATR, *NONE Attached controller . . . . . . > SNAHOST Name Mode . . . . . . . . . . . . . . > *NETATR Name, *NETATR APPN-capable . . . . . . . . . . > *YES *YES, *NO
Changes to system values
Enterprise Extender will create and use a controller QAPEND0001 on the iSeries when it communicates with remote EE systems. It will also create APPC devices under this controller when the communication is established the first time. In order for the system to automatically create the necessary controller and devices the first time, the following system values need to be changed (These values can be set back to their original settings as soon as Enterprise Extender is up and running):
QAUTOCFG: Set value to 1 (Auto-configuring of devices is on) QAUTORMT: Set value to 1 (Allow auto-configure of remote controllers) QAUTOVRT: Set value to *NOMAX (There will not be a limit on the amount of
virtual devices to be created)
Changes to Configuration lists
In order for the SNA component to work, the following changes need to be implemented on the SNA configuration lists. Use command WRKCFGL. If the *APPNLCL or *APPNRMT list do not exist, create them first.
*APPNLCL (Local APPN list):
Add the local device name to this list. This will be the name of the APPN device that the remote system will use to connect to on the iSeries. As an example, we have used SNADEVLCL.
*APPNRMT (Remote APPN List):
Add the following information to the remote list:
Remote location: Type in the name of the remote device you will use to connect to the remote system. Remote network ID: Type in the name of the remote network ID Local Location: Type in the name of the local device to which the remote network will connect to. Remote control point: Type in the System name of the remote machine Control point net ID: Type in the name of the remote network ID here again.
Opening of firewall ports
Enterprise Extender utilizes UDP ports 12000 to 12004. These ports have to be opened on all firewalls between the two systems to function.
Control-point-to-Control-point (CPCP) Sessions
If the setup has been completed, and the controllers show active on both sides, you can check to see if the sessions (CPCP) are up and running as well. Do the following:
- WRKCFGSTS *CTL QAP* (press enter)
- Take option 9 (display mode status) next to the device created for the remote system
You should see 2 modes listed. Press F11 to view the current sessions:
Mode --Sessions-- Mode Status Total Local SNASVCMG Started 0 0 CPSVCMG Started 2 1
You can also use DSPAPPNINF command to see if the system is able to communicate with the remote server. It should show whether the link is active, and if routing is valid.
Performing a communications trace
You can run a TCP/IP communications trace to see if your system is utilizing the correct ports to the remote system.
TRCCNN SET(*ON) TRCTYPE(*IP) TRCTBL(MyTraceCNN) SIZE(1000 *MB) TCPDTA(*UTP () () *N '169.202.xxx.xxx')
To print the info from the trace, TRCCNN SET(*OFF) TRCTBL(MyTraceCNN)